On an Australian earthworks site, a compaction result needs context: which material, which laboratory reference, which compactive effort and which moisture condition? A report saying “97% compaction” is incomplete unless those details are clear.
The conventional dry-density method and the rapid Hilf method both support compaction control, but they reach their results differently. This guide explains how they connect with optimum moisture content (OMC), maximum dry density (MDD), Proctor tests and field density testing.
First, separate the two meanings of “standard”
Standard compaction describes the laboratory compaction effort in AS 1289.5.1.1. Conventional compaction control commonly means using field dry density and a laboratory MDD to calculate the dry density ratio under AS 1289.5.4.1.
Hilf is a rapid control method under AS 1289.5.7.1, normally based on standard compactive effort. It is therefore possible to carry out a rapid Hilf test using standard compaction. “Standard versus rapid” and “standard versus modified” are different comparisons. See the Standards Australia descriptions for standard compaction and Hilf compaction control.
OMC, MDD and the compaction curve
A laboratory compaction test uses a specified effort to compact soil at several moisture contents. Plotting dry density against moisture content produces a compaction curve.
- Maximum dry density (MDD) is the peak dry density for that material and test effort, usually reported in t/m³ or Mg/m³.
- Optimum moisture content (OMC) is the moisture content at that peak, reported as a percentage of dry soil mass.
- Dry of optimum means moisture content is below OMC; wet of optimum means it is above OMC.
MDD is a laboratory reference, rather than an absolute physical ceiling. A field result above 100% can occur and deserves a check of material matching, reference effort and test quality.
OMC is specific to the material and method. It is not automatically the specified construction moisture target: the design may require a particular range relative to OMC. AS 1289.5.1.1 describes the standard-effort moisture–density relationship.
Proctor tests: standard and modified effort
“Proctor test” is familiar site language for a laboratory moisture–density compaction test. In Australian specifications, identify the actual AS method:
| Laboratory reference | Australian method | What to specify |
|---|---|---|
| Standard compaction, often called Standard Proctor | AS 1289.5.1.1 | Standard-effort MDD and OMC |
| Modified compaction, often called Modified Proctor | AS 1289.5.2.1 | Modified-effort MDD and OMC |
Modified effort is higher and generally produces a higher MDD and lower OMC for the same soil. Use the effort required by the project; the application alone does not decide it.
Australian test procedures should not be replaced by an ASTM procedure simply because both are called “Proctor”. See AS 1289.5.2.1.
For example, a field dry density of 1.80 t/m³ gives 97.3% against an MDD of 1.85 t/m³, but 90.0% against an MDD of 2.00 t/m³. Changing the denominator changes the reported compaction substantially.
Conventional compaction control: the dry-density route
The conventional workflow combines a representative laboratory reference with field density and moisture measurements:
- Establish the appropriate MDD and OMC using the specified laboratory compaction method.
- Measure in-situ wet density and obtain a representative field moisture content.
- Calculate field dry density.
- Calculate dry density ratio, moisture variation and/or moisture ratio as required.
AS 1289.5.4.1 addresses these compaction-control parameters. Assignment of reference MDD and OMC values is addressed separately by AS 1289.5.4.2; a borrowed curve should not be used merely because the soil looks similar.
For the equations below, w is moisture content entered as a percentage number, so 12% is entered as 12:
Field dry density = field wet density ÷ (1 + w/100)
Dry density ratio (%) = field dry density ÷ reference MDD × 100
Moisture variation = field moisture content − OMC
Moisture ratio (%) = field moisture content ÷ OMC × 100
The density ratio is commonly called relative compaction (RC). Keep the report’s method-specific terminology, particularly when comparing it with a Hilf result.
Worked example: density and moisture are separate checks
Assume a matched material reference and no oversize correction:
| Input | Value |
|---|---|
| Field wet density | 2.04 t/m³ |
| Field moisture content | 12.0% |
| Standard-effort MDD | 1.88 t/m³ |
| Standard-effort OMC | 14.0% |
Field dry density = 2.04 ÷ 1.12 = 1.821 t/m³.
Dry density ratio = 1.821 ÷ 1.88 × 100 = 96.9%.
Moisture variation = 12.0 − 14.0 = −2.0 percentage points, or 2 points dry of optimum.
Moisture ratio = 12.0 ÷ 14.0 × 100 = 85.7%.
If a hypothetical specification requires a minimum individual density ratio of 95%, the density result meets that criterion. Moisture acceptance still depends on the specified range, and lot acceptance may require additional tests or statistical assessment. These figures are an illustration, not a universal Australian acceptance requirement.
Rapid compaction control: the Hilf method
Hilf relates laboratory converted wet density (CWD) to controlled moisture additions or removals. The conversion puts results on a common basis related to the original field sample, avoiding the need to await moisture-content determinations to obtain the rapid control parameters.
For material without oversize correction:
Hilf density ratio (%) = field wet density ÷ peak converted wet density × 100
The method also provides Hilf moisture variation. It does not directly produce a conventional dry-density curve, MDD and OMC. Those values require additional moisture information and the applicable calculations.
For example, field wet density of 2.04 t/m³ and peak CWD of 2.10 t/m³ give a Hilf density ratio of 97.1%. Dividing by the highest unconverted laboratory wet density would be incorrect.
AS 1289.5.7.1 defines the rapid method. Its scope warns about soils far from optimum, limits added moisture Z to −4% to +6%, and requires soil-specific experimental support for reliable moisture variation with modified effort. Minor differences from conventional results can occur. Consult the full standard for its scope, corrections and procedural limits.
Conventional versus Hilf: practical comparison
| Question | Conventional dry-density control | Rapid Hilf control |
|---|---|---|
| Main reference | Laboratory MDD | Peak converted wet density |
| Reported density parameter | Dry density ratio | Hilf density ratio |
| Moisture assessment | Measured moisture compared with OMC | Hilf moisture variation |
| Main advantage | Direct connection to MDD, OMC and the moisture–density curve | Earlier feedback during earthworks |
| Main planning issue | Allow time for representative moisture and reference testing | Confirm suitability, limits and project approval |
Choose the method before testing, through the specification and inspection and test plan (ITP). Do not change methods solely to obtain a passing result.
Field density testing and the nuclear density gauge
A nuclear density gauge (NDG) provides field measurements used in compaction control. AS 1289.5.8.1 covers a nuclear surface moisture–density gauge operating in direct transmission mode. This is a field measurement method, separate from either laboratory reference route. See AS 1289.5.8.1.
The gauge uses radiation response to assess density and moisture-related properties. Dry density and percentage compaction are calculated using moisture information and a selected reference; the instrument does not independently establish the soil’s MDD. The Canadian Nuclear Safety Commission’s explanation describes the measurement principles.
For reliable site results, confirm that:
- The test location represents the nominated lot and layer.
- The test depth and layer thickness are compatible with the prescribed procedure.
- Surface preparation, gauge seating and probe-hole preparation meet the method.
- Calibration, routine checks and required material-specific corrections are valid.
- The associated sample represents the material tested by the gauge.
- The entered laboratory reference belongs to that material and compactive effort.
A fast gauge reading does not make the complete compaction assessment instantaneous. Sampling, laboratory testing, calculations and review still matter.
Sand replacement and moisture testing
Sand replacement is another field-density option where suitable and permitted. AS 1289.5.3.1 uses a sand-cone apparatus; AS 1289.5.3.2 uses a sand-pouring can. Excavated soil mass and measured hole volume establish wet density, with representative moisture testing needed for dry density. Method selection depends on material and site conditions. The Standards Australia catalogue identifies the sand-cone method.
AS 1289.2.1.1 is the oven-drying moisture method. Do not confuse microwave drying, AS 1289.2.1.4, with a calcium-carbide “Speedy” moisture tester. Any alternative moisture method must be permitted and appropriately verified for its intended use; the NT roadworks specification lists the relevant Australian method references.
NDGs contain radioactive sources. Use appropriately authorised operators and comply with the relevant state or territory requirements for possession, use, storage and transport. ARPANSA RPS 5 provides the national code and safety guide; licensing requirements are jurisdiction-specific.
Which Australian standards and specifications apply?
| Reference | Role in the testing programme |
|---|---|
| AS 1289.2.1.1 | Oven-drying moisture content |
| AS 1289.5.1.1 / 5.2.1 | Standard / modified laboratory compaction |
| AS 1289.5.4.1 | Dry density ratio and moisture control parameters |
| AS 1289.5.4.2 | Assignment of reference MDD and OMC |
| AS 1289.5.7.1 | Rapid Hilf compaction control |
| AS 1289.5.8.1 | Direct-transmission nuclear field testing |
| AS 1289.5.5.1 / 5.6.1 | Laboratory limiting densities / density index control for cohesionless material |
| AS 3798 | Guidance for commercial and residential earthworks |
These references perform different jobs. The test method describes how to measure; the project specification establishes acceptance.
AS 3798 is guidance rather than a complete earthworks specification. Its stated scope excludes pavements, major roadworks and water-retaining structures, which need separate consideration.
For Queensland roadworks, TMR MRTS04 General Earthworks links compaction verification to material category and location. Cohesionless sand and coarse or rock fill can require different approaches. Density index is not interchangeable with a percentage of Proctor MDD.
NSW projects can specify TfNSW methods and lot-based acceptance. The TfNSW earthworks specification also treats moisture conformity explicitly. Check the contract edition, annexures and current method identifiers rather than assuming requirements are identical across states, councils and utilities.
Reading the report and responding on site
Before releasing a layer, check the location, reduced level (RL), lot and lift identification; material description; field and reference methods; compactive effort; density ratio; moisture result; and applicable acceptance criteria. Record any oversize correction and limitations. Maintain traceability between the field test and laboratory sample.
Where NATA-endorsed testing is required, check the laboratory’s scope for the actual methods and field activities. Accreditation does not automatically cover every service a laboratory offers. NATA explains how to choose the right laboratory.
| Finding | Practical next step |
|---|---|
| Low density, material dry of the specified range | Review water addition and mixing, then recompact and retest under the approved procedure |
| Low density with pumping or excessive moisture | Assess drying, drainage and material condition before further rolling |
| Density passes but moisture fails | Address the moisture nonconformity; the density result alone does not release the lot |
| Unexpectedly high density ratio | Check the reference, effort, material changes, oversize treatment and field measurement |
| Source or grading changes | Confirm whether a new reference test or reassessment is needed |
| Soft response despite passing density | Investigate underlying support, layer thickness and material behaviour |
More roller passes are not a universal remedy. A density result also does not establish CBR, stiffness, bearing capacity or overall platform suitability. Proof rolling and strength or stiffness tests answer different questions and must be used as specified.
Does 95% compaction mean 5% air voids?
No. It means the measured density parameter is 95% of the specified reference density parameter. Air voids require a separate assessment using additional material properties.
Is a Hilf test the same as a nuclear gauge test?
No. Hilf supplies a laboratory-based compaction-control reference and associated results. The NDG supplies field measurements. They can form parts of the same testing workflow.
Can a single passing test certify the whole fill platform?
A test represents its nominated location and sampling context. Acceptance depends on the specified coverage, lot rules, inspections and any required geotechnical assessment. Plan testing before covering the layer.