Flexural strength testing measures the calculated bending stress at which a concrete test beam breaks. It matters for rigid concrete pavements because repeated wheel loads bend slabs and can lead to cracking.
In Australia, flexural strength (also called the modulus of rupture) is determined in accordance with AS 1012.11 (Determination of the modulus of rupture). Beams are loaded at the third points of their span. Specimens are made and cured to AS 1012.8.2. Road authority pavement specifications, such as TfNSW R83, set the required 28-day flexural strength and the conformity rules.
Concrete is much weaker in tension than in compression. A typical pavement concrete with a compressive strength of 40 MPa may have a flexural strength of only around 4.5–5 MPa. That is why pavement design is based on flexural strength rather than compressive strength.
At a glance: a beam test measures bending strength, commonly for pavements. Correct moisture condition, support span, total load and fracture location are essential to interpreting the number.
Terms Explained
| Term | Plain-English meaning |
|---|---|
| Flexure | Bending. A loaded beam has compression on one side and tension on the other. |
| Modulus of rupture | The calculated extreme-fibre tensile stress when the test beam breaks. It is a strength result, not a stiffness measurement. |
| Tension face | The stretched face of the beam, normally the bottom face in this test. Damage or drying here can strongly affect the result. |
| Third-point loading | Two equal loads applied one-third and two-thirds of the distance between the supports. |
| Span | The distance between support centres, not the beam’s full length. |
| Total machine load | The combined force carried by both loading points. Using half this force in the formula halves the calculated result incorrectly. |
| SCMs | Supplementary cementitious materials, such as fly ash or slag, used as part of the binder. |
| Residual strength | Load-carrying capacity after cracking, particularly relevant to fibre-reinforced concrete. It requires the specified post-cracking test. |
Where Flexural Strength Testing Is Used
- Plain, jointed and continuously reinforced concrete road pavements. Fibre-reinforced concrete needs the specified residual/post-cracking performance tests as well; a modulus-of-rupture result alone does not characterise fibre performance
- Airport runways, taxiways and aprons
- Industrial floors, hardstands and container yards designed by flexural methods
- Precast elements such as kerbs and slabs where flexure governs
- Mix design trials for pavement concrete
- Research and correlation testing between flexural and compressive strength
For most building structures designed to AS 3600, flexural tensile strength is estimated from compressive strength rather than tested.
Australian Standards and Specifications
| Standard / Document | Relevance |
|---|---|
| AS 1012.8.2 | Making and curing flexure test specimens (beams) |
| AS 1012.11 | Modulus of rupture by third-point loading of simple beams |
| AS 1012.10 | Indirect tensile (Brazil or splitting) strength of cylinders, an alternative tensile test |
| AS 3600 | Characteristic flexural tensile strength used in design |
| Austroads Guide to Pavement Technology Part 2 | Rigid pavement design based on 28-day flexural strength |
| TfNSW R83 | Concrete pavement base; minimum flexural strengths, testing and conformity |
| TfNSW T304 | Moulding of specimens by vibration for R83 work |
| TMR MRTS40 and related specs | Concrete pavement requirements in Queensland |
Test Specimens
Beams are cast in rigid steel moulds in accordance with AS 1012.8.2. Common sizes are:
| Beam Size (Width × Depth × Length) | Typical Use |
|---|---|
| 100 × 100 × 350 mm | Concrete with nominal aggregate up to about 20 mm |
| 150 × 150 × 500 mm | Larger aggregate and some specifications |
Beams are compacted by rodding or vibration as the standard and specification require. Road authority specifications can set the size and compaction method. For example, TfNSW R83 uses standard 100 × 100 × 350 mm beams moulded to RMS T304, compacted by internal or table vibration.
Young beams are fragile. Plan initial curing, demoulding and transport under AS 1012.8.2 and the adopted specification, with support and protection against bending damage. A nominal collection day does not demonstrate that handling is permitted. Maintain the prescribed moist curing until testing.
Flexural Strength Test Procedure
1. Keep the Beam Wet
Test beams immediately after removal from moist curing, with the surfaces still wet. Even a short period of surface drying creates tensile stresses on the surface and can noticeably reduce the measured modulus of rupture.
2. Set Up Third-Point Loading
Place the beam on two support rollers with the span set at three times the depth. Two loading rollers apply equal loads at the third points of the span. That gives a zone of constant bending moment in the middle third, with no shear.
The beam is turned on its side relative to its moulded position, so the loads are applied to smooth moulded faces.
3. Apply the Load
Load continuously and without shock at the rate set by the standard until the beam breaks. Record the maximum load.
4. Measure the Beam at the Fracture
Measure the average width and depth of the beam at the fracture section, and the position of the fracture relative to the supports.
5. Calculate the Modulus of Rupture
If the fracture starts in the middle third of the span:
Flexural strength = (P × L) ÷ (b × d²)
where:
- flexural strength is the modulus of rupture (flexural strength) in MPa
- P is the total maximum machine load in N, shared equally between the two loading points (not the load at one point)
- L is the span between supports in mm
- b is the average width at the fracture in mm
- mean diameter is the average depth at the fracture in mm
If the fracture occurs outside the middle third, the result is treated as AS 1012.11 directs. A fracture well outside the middle third usually indicates a defect or a loading problem, and the result may need to be discarded.
Check below for an example:
A 150 × 150 mm beam tested over a 450 mm span breaks in the middle third at 34.0 kN. The measured width and depth at the fracture are 151 mm and 150 mm.
Flexural strength = (34,000 × 450) ÷ (151 × 150²) ≈ 4.5 MPa, before applying the method’s reporting rule.
What a Beam Result Can Tell the Project
In the worked example, 4.5 MPa is the stress calculated for that beam under the stated loading arrangement. It is not interchangeable with a 4.5 MPa direct-tension result or a 40 MPa cylinder grade.
Before testing, agree whether the requirement is for a trial mix, process control, a lot assessment or an early opening decision. A lot is the defined quantity of work assessed together. The specification determines how many valid beams represent it and whether individual results, averages or statistical criteria govern.
If a beam result is low, retain the result and check surface drying, transport damage, compaction, dimensions, load arrangement and fracture location. The laboratory decides method validity under its procedure; the project’s nominated reviewer decides the contractual consequence. A higher cylinder result cannot substitute for a required flexural result unless the specification expressly permits a validated relationship.
Flexural Strength Requirements
The required flexural strength comes from the pavement or floor design and the specification. Road authority specifications such as TfNSW R83 set minimum 28-day flexural strengths for trial mixes and for concrete in the work, with different values depending on whether the mix contains supplementary cementitious materials. Pavement concrete is commonly specified at around 4.5 to 5.0 MPa at 28 days, and industrial floors designed by flexural methods are often in a similar range.
Requirements depend on the specification edition and the pavement type, and some specifications also set an upper limit for continuously reinforced pavements to control cracking. Check the edition your contract cites.
Relationship to Compressive Strength
AS 3600 estimates the characteristic flexural tensile strength from the compressive strength:
Characteristic flexural tensile strength = 0.6 × √f′c (strengths in MPa).
For 40 MPa concrete:
0.6 × √40 ≈ 3.8 MPa.
This is a characteristic (lower) design value for structural design. Measured modulus of rupture values from well-cured pavement beams are usually higher. Pavement design uses project-specific tested flexural strength rather than this estimate.
The ratio between flexural and compressive strength depends strongly on aggregate type, shape and texture. Crushed, angular aggregates generally give higher flexural strength than rounded gravels at the same compressive strength. That is one reason pavement mixes are proven by trial.
Flexural vs Indirect Tensile vs Direct Tension
| Test | Standard | Notes |
|---|---|---|
| Flexural (modulus of rupture) | AS 1012.11 | Most relevant to pavements; gives the highest of the three tensile values |
| Indirect tensile (Brazil) | AS 1012.10 | Uses standard cylinders; simpler to make and transport; lower values than flexure |
| Direct tension | Research methods | Most "pure" tensile measure but rarely used in practice |
Fibre-Reinforced Concrete
AS 1012.11 notes that its relevance to fibre-reinforced concrete is still under investigation. Fibre-reinforced concrete is normally assessed for post-cracking performance (residual strength), which a modulus of rupture test doesn't capture. Methods such as EN 14651 (notched beams) or round determinate panel tests (ASTM C1550) for sprayed concrete are typically specified instead.
Low Flexural Results?
| Cause | Effect |
|---|---|
| Beam allowed to dry before testing | Significantly lower modulus of rupture |
| Poor compaction | Voids at the tension face |
| Handling damage during transport | Micro-cracks; very low or erratic results |
| Loading on rough trowelled or uneven faces | Uneven loading, premature failure |
| Fracture outside the middle third | Result may be invalid |
| Rounded aggregate or poor aggregate bond | Lower flexural strength for the same compressive strength |
Remember...
- Make enough beams for 7 and 28-day tests plus spares; beams are easily damaged
- Transport beams in padded racks, lying on a long face
- Cure in moist conditions from stripping until test
- Test straight out of curing; don't let the beams dry
- Make beams and cylinders from the same sample to build a project-specific correlation
- Report the fracture location for every beam
Recording Flexural Results in a LIMS
A LIMS records each beam with its nominal size from moulding, the span of the flexure frame it was broken in, the section measured at the fracture, the force and where the beam broke. A beam that breaks outside the zone the method accepts is recorded as giving no flexural strength, so it cannot slip into an average. See Part 5: Break the cylinders and beams of Concrete Testing in a LIMS. Whatever system you use, verify the configured method, calculation rules and report wording against the laboratory’s controlled procedure; software output does not itself establish standards compliance or authorise construction work.
Frequently Asked Questions
What is the modulus of rupture?
It is the maximum tensile stress at the bottom of a beam at failure, calculated from simple bending theory. In Australian practice it is the flexural strength measured by AS 1012.11.
Why is flexural strength used for pavement design?
Concrete pavements fail by cracking under repeated bending from wheel loads. Flexural strength directly measures resistance to that type of failure.
What is a typical flexural strength for road pavement concrete?
The project specification sets the requirement. Values around 4.5–5.0 MPa give a sense of scale, but the nominated authority specification and design set the actual requirement. Trial-mix, process-control and lot acceptance criteria may differ; record which one is being assessed.
Can flexural strength be calculated from compressive strength?
AS 3600 gives a characteristic estimate of 0.6√f′c for structural design. For pavements, the specification usually requires the flexural strength to be tested.
What happens if the beam breaks outside the middle third?
The calculation for a middle-third fracture is no longer valid. Follow AS 1012.11 for how to treat or discard the result, and investigate the cause.
Sources and Method Scope
This learning guide explains purpose, terminology and interpretation. It is not the full test method. Use the project-adopted standards, amendments, specification and controlled laboratory procedure for exact apparatus, timing, conditioning, calculations and decision rules.
-
CCAA Guide to Concrete Construction (2020) — Part VIII, Section 26 gives background on testing and quality assurance.
-
Standards Australia — AS 1379:2026 catalogue entry; obtain the project-adopted standards and amendments for detailed requirements