Post-Tension Early Age Concrete Testing

Plan early-age testing for post-tensioning and understand the strength evidence, curing and approval needed before stressing.

Table of contents

Post-tension early age testing confirms that a post-tensioned slab or beam has gained enough strength to be stressed safely. Cylinders made from the relevant concrete are tested at planned early ages under an approved curing regime intended to represent the works. The stressing contractor proceeds only after the required strength and other release conditions have been checked and the nominated authority has authorised stressing.

It is one of the highest-consequence concrete tests on an Australian building site. Stressing before the concrete and anchorage zones are ready can cause severe local failure. Agree a test schedule and spare specimens before the pour so a delay can be managed without changing the release criteria.

In Australia the cylinders are moulded to AS 1012.8.1 and crushed to AS 1012.9, like any other compression test. The difference is how they are cured and how the result is used. As PTIA guidance points out, AS 3600 requires early-age specimens for stressing decisions to be cured under conditions similar to those of the concrete in the works. The Post-Tensioning Institute of Australia (PTIA) publishes widely used guidance on stressing strengths.


The following historical slab-system example helps explain the difference between initial and final stressing. The approved project may use a different sequence or requirements.

Stage Typical Force Applied Typical Concrete Strength Required
Initial stressing About 25% of the prestressing force About 7–9 MPa
Final stressing 100% of the prestressing force About 22 MPa for 12.7 mm strand; 25 MPa for 15.2 mm strand

Historical examples from PTIA slab system guidance dated 16 July 2007, for the slab systems discussed there. They are not universal stressing strengths and must not be extrapolated to multistrand systems. The approved design, anchorage system requirements and project specification govern.

  • Initial stressing is usually done within a day or so of the pour. It puts a small compression into the slab to control early shrinkage cracking before the slab is strong enough for full stress.
  • Final stressing is usually done between day 3 and day 7, often at day 4 or 5 on a typical high-rise floor cycle.

The anchorage zone is where the risk concentrates. The full tendon force bears on a small area of young concrete behind the anchor. That local bearing capacity depends on the concrete's strength at the time of stressing, not its 28-day strength.

At a glance: early-age strength testing supports a planned stressing decision. Representative curing, the approved decision rule and written release are essential; reaching a number is only part of the evidence.

Terms Explained

Term Plain-English meaning
Post-tensioning (PT) Tensioning steel tendons after concrete has hardened so they apply compression to the concrete.
Tendon, strand and anchorage A tendon is the prestressing assembly; strand is high-strength steel within it; anchorages transfer its force into the concrete.
Stressing or transfer strength The concrete strength required when prestress is applied. It is separate from the specified later-age grade.
Anchorage zone The concrete around an anchorage where concentrated tendon force spreads into the member.
Bursting and spalling Local tensile effects that can split concrete internally or break material from a surface near an anchorage.
Representative curing An approved specimen-curing arrangement intended to reflect the relevant concrete in the works, supported by records of conditions.
Maturity An index calculated from time and temperature history. A validated relationship for the actual mix is needed to estimate strength.
Hold-point release The nominated authority’s documented permission to proceed after reviewing all required evidence—not merely receipt of a strength report.

Standards and Guidance

Document Relevance
AS 3600 Concrete structures; prestressed design; transfer strength; early-age specimens cured similar to the works
AS 1012.8.1 Making and curing cylinders
AS 1012.9 Compressive strength test
AS 1379 PT concrete with an early age strength requirement is specified as special-class concrete
AS 5100.5 Bridge design, concrete (prestressed bridge elements)
PTIA guidance Slab system concrete requirements for early age stressing; practical prestress detailing
TfNSW B113 Post-tensioning of concrete (NSW bridges and road structures)
ASTM C1074 / TfNSW TS 02800.56 / DTP (VicRoads) Section 610 Maturity method for estimating in-place early-age strength

Early Age Testing

1. Specify the Early Age Strength

The structural or PT designer specifies:

  • The initial stressing strength (e.g. 7 MPa)
  • The final stressing strength (e.g. 22 or 25 MPa)
  • The minimum age for final stressing, where relevant

The concrete is ordered as special-class concrete under AS 1379 with that early age requirement, and the supplier designs the mix to reach it within the builder's floor cycle.

2. Plan the Number of Cylinders

Make enough cylinders for every stressing decision, plus spares. A common arrangement for each pour is:

Purpose Typical Number of Cylinders
Initial stressing check 2
Final stressing check 2 per planned test age (e.g. day 3, plus day 4 as a backup)
Spares (in case strength isn't reached) 2 or more
28-day conformity Per normal project sampling plan

Sampling from more than one truck, including late trucks placed near the slab edges, gives a better picture than sampling from only the first load.

3. Cure the Cylinders on Site

Agree a curing plan that represents the concrete in the works, as required for the construction decision. Record specimen location, protection and temperature history. Simply putting a small cylinder beside a slab does not reproduce the slab’s internal temperature: thermal mass, insulation and exposure differ.

Use project-approved representative site curing or temperature-matched curing where specified. Keep standard-cured conformity specimens separately identified. Arrange collection and transport to avoid changing or damaging the early-age specimens, and follow the approved method and PT designer’s requirements.

4. Test and Report Quickly

The laboratory collects the cylinders and crushes them on the morning of the planned stressing day. The results go straight to the builder, PT contractor and engineer, under the turnaround and notification arrangements agreed before the pour.

5. Make the Stressing Decision

The strength report is evidence for a hold-point release, not permission to stress. The nominated release authority must check the specified strength and minimum age, representative curing, anchorage and reinforcement condition, equipment calibration, stressing sequence and exclusion zones before issuing the required written release.

Use the contract’s decision rule: it may require each cylinder or an approved sample statistic. Do not switch between these rules to obtain a pass. Investigate questionable results and document any method-authorised exclusion through technical review. If a requirement is unmet or uncertain, keep the hold point closed and obtain direction from the PT/structural designer; test planned spare specimens when directed.

Worked Decision Example

Assume, for illustration, an approved PT instruction requires each of two representative cylinders to reach 25 MPa. Results are 24.5 and 26.0 MPa. Their mean is 25.25 MPa, but the stated rule is not met because one cylinder is below 25 MPa. Averaging would change the decision rule.

If the project instead specifies a sample mean, use that approved rule together with any individual-result, minimum-age and other conditions. In either case, check curing relevance and obtain the written release. When the evidence is insufficient, retain the hold point and ask the designer to direct the next test or action.

Factors That Slow Early Strength Gain

Factor Effect
Cold weather (winter in Melbourne, Canberra, Hobart, inland areas) Much slower strength gain; a 4-day stress may need 5 or 6 days
High fly ash or slag content Lower early strength and slower early tensile strength gain
Low cement content Slower strength gain
Retarding admixtures Delayed set, lower early strength
High water content Lower strength at all ages
Thin slab edges and exposed corners Cool faster than the slab's core

The mix must satisfy the PT designer’s early-age performance and anchorage-system requirements as well as later-age strength and durability requirements. Compressive strength alone does not describe early tensile or bond behaviour. Resolve binder composition and early-age performance through the approved mix design and trials; do not select a universal cement-content limit from historical guidance.

Anchorage Zone Risks

Many anchorage zone failures in post-tensioned members have occurred at the stressing stage. Research on Australian practice links them to inadequate early compressive strength combined with temperature effects and poor compaction.

To reduce the risk:

  • Compact concrete thoroughly around every anchorage, which is vital for force transfer
  • Don't stress before the specified strength and age are confirmed
  • Pay attention to anchorages near the slab edges and those placed last, where concrete may be cooler or less well compacted
  • Check anchorages and the bursting zone visually after stressing
  • Report any cracking or spalling at anchors to the PT designer immediately

Alternatives and Supplements to Site-Cured Cylinders

Method How It Works Notes
Site-cured cylinders Cylinders stored next to the slab and crushed at the stressing age The standard Australian approach
Temperature-matched curing Cylinders cured in a bath that follows the measured slab temperature More representative; used on major projects and in research
Maturity method (ASTM C1074) Temperature sensors in the slab plus a mix-specific strength–maturity calibration estimate in-place strength in real time Recognised by some Australian road authorities (e.g. TfNSW TS 02800.56, DTP Section 610); calibration must be specific to the mix
Rebound hammer Surface hardness compared with a calibration A supplementary check only (see Schmidt Hammer Testing)

The maturity method can help optimise the floor cycle. It still needs cylinder breaks to build and verify the calibration. It also doesn't replace 28-day cylinder testing for conformity.

Early Age Testing Program Checklist

  • Early age strengths and minimum ages are clearly shown on the PT drawings and in the ITP
  • Concrete is ordered as special-class with the early age requirement
  • The laboratory knows the stressing dates and testing times
  • Enough cylinders are made, including spares
  • Cylinders are labelled with the pour, stressing purpose and planned test age
  • The approved representative curing regime and temperature history are documented; conformity specimens remain separately identified
  • Results are sent to the builder, PT contractor and engineer before stressing
  • Stressing records reference the cylinder results used
  • 28-day cylinders are taken and tested as usual

Reporting Stressing Checks in a LIMS

For a stressing decision, a LIMS records the strength required for stressing with the load, tests each early cylinder at its age, and states on the report whether the cylinders at that age reached it, judged the way the project specifies. The cylinders' path from site to the breaking session is shown in Part 4: Pick up and cure the specimens and Part 5: Break the cylinders and beams of Concrete Testing in a LIMS. Whatever system you use, verify the configured method, calculation rules and report wording against the laboratory’s controlled procedure; software output does not itself establish standards compliance or authorise construction work.

Frequently Asked Questions

What strength is needed before stressing a PT slab?

Use the approved PT drawings, anchorage-system requirements and project specification. The numerical values shown earlier are historical examples for particular slab systems, not instructions for a current stressing operation.

Why are early age cylinders cured on site?

They are intended to represent early strength in the works. Site curing needs a planned, recorded regime; adjacency alone does not guarantee equivalent temperature or strength. Use the project-approved curing or temperature-matching approach.

What happens if the cylinders haven't reached the stressing strength?

Don't stress. Wait and test spare cylinders later, or follow the engineer's direction. Stressing early risks anchorage failure.

Can maturity sensors replace cylinders for PT stressing?

They can estimate in-place strength in real time once calibrated for the mix, and some projects use them to plan stressing. Many projects still require cylinder confirmation. Check the specification and the engineer's requirements.

Does early age testing replace 28-day testing?

No. Early age results are for construction decisions. Conformity of the concrete is still assessed on 28-day (or 56-day) cylinders under AS 1379.


Sources and Method Scope

This learning guide explains purpose, terminology and interpretation. It is not the full test method. Use the project-adopted standards, amendments, specification and controlled laboratory procedure for exact apparatus, timing, conditioning, calculations and decision rules.

Related Resources